banner



How To Install A Fill Valve

Download Article

Download Article

A faulty toilet fill valve can cause your toilet to run all the time or otherwise malfunction. Yet, the good news is that replacing your toilet fill up valve is something any homeowner can practice. It does non take a lot of experience with plumbing or a lot of time. However, you do need a few parts, a couple of tools, and a little fleck of endeavour.

  1. i

    Turn off the h2o supply. Before doing any repairs to your toilet yous should plough off the water outside of the toilet. You should have a water valve straight below the toilet tank. It should be located between where the h2o pipe comes out of the wall and where it attaches to the bottom of the toilet tank.[one]

    • In nearly cases, you will turn the water shutoff valve clockwise to plough it off. Be sure to go on turning it until information technology stops moving.

    EXPERT TIP

    James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. James has over 32 years of home service and business concern plumbing experience and has expanded the Twin Home Experts to Phoenix, Arizona and the Pacific Northwest.

    James Schuelke

    James Schuelke
    Professional person Plumber

    It's a good idea to plough off your principal water valve, equally well. Notice the master water close-off valve on the exterior of your home and turn it off. And then, go around your property and plough on various fixtures to confirm that they're off, but it volition also drain off residual water that'southward inside the system. Doing this volition help you avert water damage due to a flood.

  2. 2

    Drain the toilet tank. Once the water is turned off, bleed the tank earlier you lot can disconnect the toilet fill valve. To begin draining the tank, flush the toilet and hold the flush lever down to remove as much water as possible. In one case most of the h2o is gone, y'all will need to utilise a turkey baster or a wet-dry vacuum to get rid of the small amount of water sitting at the bottom of the tank.[two]

    • If you don't accept a turkey baster or wet-dry vacuum, use an old towel or sponge to soak upwards the remaining water and whatever sediment left in the tank.

    Advertisement

  3. 3

    Locate the toilet make full valve. Remove the tank hat carefully and set it on a towel out of the way so it doesn't get broken. The toilet fill up valve is located inside the toilet tank, usually off to one side. In newer toilets, it is the unabridged plastic column that includes the bladder and the on-off lever for filling. In older toilets, the bladder is a divide piece just it will exist connected to the top of the fill valve. [3]

    • The fill up valve likewise has a tube fastened to it that connects to the overflow pipe.[4]
  4. iv

    Disassemble the toilet fill valve. Loosen the nut that secures the fill up valve to the water supply line by turning information technology counterclockwise with pliers or a wrench. Then, carefully pull the supply line out of the valve underneath the tank.[5]

    • Equally yous unscrew the nut, a bit of water may drip out of the tank. Proceed a towel on paw or on the floor beneath the opening to catch whatsoever water that comes out.

    Advertising

  1. 1

    Purchase a new toilet fill valve. Go to your local hardware store and buy a new toilet fill valve. Most new toilet fill up valves are universal, pregnant they will fit in nigh whatsoever toilet. However, if you are worried about fit, take your old toilet valve with you to the store and use it to assess whether a potential replacement will piece of work.[vi]

    • Even if your onetime toilet fill valve had a carve up float, a newer valve with the float integrated onto the shaft will piece of work.
  2. 2

    Put the new toilet fill valve in place. Remove the new toilet fill valve from its packaging. Be sure to read the directions it comes with. The fill valve should come fully assembled, so you should be able to put it straight into the toilet.[7]

    • Remember to also clip the new refill tube to the overflow tube.
  3. 3

    Make sure all the washers are in identify. It is of import to pay attending to how whatever included washers and basics should exist attached to the valve. At that place should be washers on the inside and the exterior of the tank where the make full valve goes through it.[8]

    • Washers on the inside and outside of the tank ensure that there is a water-tight seal around this connection point.
  4. 4

    Tighten the fill valve nut carefully. When y'all take the toilet fill valve in identify, the final function of its installation is to tighten a lock nut onto the threaded role of the valve. This is located on the underside of the tank. When doing this, information technology is important not to tighten the nut too hard. The nut should be tightened by mitt to ensure that y'all don't tighten it too much.[9]

    • Tightening the nut on the bottom of the make full valve with a wrench or pliers could scissure the toilet tank or the valve.
  5. v

    Reattach the h2o supply line and plough on the water. Once the replacement fill valve is in place, it's time to get the water flowing again. Attach the supply line to the bottom of the new make full valve. Make sure that there is a washer inside the terminate of the supply line and tighten it with a wrench until it's tight. Then turn on the water by turning the shutoff valve counter clockwise until it stops rotating.[x]

    • Be conscientious not to overtighten the washer, or the nut could fissure and the connection will leak.
    • If you see any leaks, immediately turn the water off at the shutoff valve.
    • When yous turn the water on, the tank should showtime filling right abroad.

    Good TIP

    James Schuelke, forth with his twin blood brother David, is the co-owner of the Twin Dwelling Experts, a licensed plumbing, leak detection, and mold inspection visitor based in Los Angeles, California. James has over 32 years of home service and business plumbing feel and has expanded the Twin Home Experts to Phoenix, Arizona and the Pacific Northwest.

    James Schuelke

    James Schuelke
    Professional person Plumber

    Be very cautious every bit you plow the water back on. One time the valve is on, turn the main h2o supply on very slowly, and have a second person go into the bathroom and make certain there are no leaks as y'all regenerate the water system.

  6. vi

    Suit the float. Once the h2o is turned dorsum on and your toilet tank has filled, then you tin adjust the float on your new toilet make full valve. The float's location can be adjusted with a clip on its side, a set screw at the superlative of the float shaft, or past adjusting a screw at the elevation of fill valve where the float attaches.[11]

    • Look at the directions of your new toilet fill valve for verbal directions for float adjustment.
    • When positioned correctly, the summit of the float should be set at about 1 inch (two.v cm) beneath the top of the overflow pipe. The goal is that the float comes up and shuts off the h2o earlier the water gets high enough to flow over the top of the overflow pipage.

    Advert

Inquire a Question

200 characters left

Include your email address to go a message when this question is answered.

Submit

Advertizement

  • If the fill valve is malfunctioning on an older three.5-gallon (13.25-liter) flush toilet, consider replacing the toilet with a 1.v-gallon (5.67-liter) model. It will hands pay for itself in water savings!

Advertisement

Things You'll Need

  • A wrench or pliers
  • New toilet fill up valve kit
  • Bucket
  • Towel

Most This Article

Commodity Summary X

To supplant a toilet fill valve, offset by turning off the water valve directly below the toilet. Next, flush the toilet and hold the lever down to remove as much water as possible from the tank. You can get rid of any excess water by using a turkey baster, wet-dry out vacuum, or erstwhile towels. And so, remove the tank lid and locate the toilet fill valve, which should be off to one side and connected to the overflow piping. Detach the valve and put the new valve in its identify, remembering to clip information technology to the overflow pipe. Finally, tighten downward all the washers and basics to secure the valve in place, and turn the water back on. To learn how to arrange the float on your new toilet make full valve, proceed reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 153,873 times.

Did this article assistance you?

Source: https://www.wikihow.com/Replace-a-Toilet-Fill-Valve

Posted by: harbinforrounce.blogspot.com

0 Response to "How To Install A Fill Valve"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel